Class 9 Physics Notes (Unit-1) Punjab Boards

 Physics 9th Class Notes by 

Physics Notes.Online


Chapter No. 1


Physical Quantities and Measurement






Exercise Short Questions:


Q1: Can a non-physical quantity be measured? If yes then how?


Ans. No, a non-physical quantity (emotions, feelings, ideas) cannot be measured. There is no method to measure it.


Q2: What is measurement? Name its two parts.


Ans: Measurement is the process of obtaining a numerical value for a physical quantity. Its two parts are:


1. Numerical value


2. Unit of measurement


Q3: Why do we need a standard unit for measurements? 


Ans A standard unit ensures uniformity and consistency across measurements making it possible to compare results globally and accurately.


Q4: Write the name of 3 base quantities and 3 derived quantities.


Ans: Base Quantities:


1. Length 2. Mass 3. Time


Derived Quantities:


1. Speed 2. Area 3. Volume



Q5: Which Sl unit will you use to express the height of your desk?


Ans: The SI unit used to express the height of a desk is metre (m).


Q6: Write the name and symbols of all Sl base units.


Ans:


1. Length-meter (m)


2. Mass-kilogram (kg)


3. Time-second (s)


4. Electric current-ampere (A)


V. Temperature-kelvin (k)


vi. Intensity of light-candela (cd)


vii. Amount of substance-mole (mol)


Q7: Why is prefix used? Name three sub-multiples and three multiple prefixes with their symbols.


Ans: Prefixes are used to write units by power of 10. It is also used to represent very large or very small numbers in a more convenient way.


Sub-multiples


1.milli (m) = 10 ^ - 3


2. micro (mu) = 10 ^- 6


3. nano (n) = 10 ^ -9


Multiples:


i. kilo (k) = 10 ^ 3

ii. mega 10^6

iii. giga (G) =10^9


Q8: What is meant by:


Ans:


a. 5 pm = 5 picometre = 5x10-12 meters


b. 15 ns =15 nanosecond = 15x10-9 seconds


c. 6 µm = 6 micrometre = 6x10-6 meters d. 5 fs =5 femtosecond = 5 * 10 ^ - 15 seconds


Q9: (a) For what purpose, a Vernier Callipers is used?


Ans: Vernier Callipers are used to measure length with high precision, typically up to 0.1 mm.


(b) Name its two parts.


Ans:


1. Main scale


il Vernier scale


(c) How is the least count found?


Ans: Least count is found by the difference between one main scale division (M.S) and Vernier scale division (V.S).


Hence Least Count = 1M.S div-1V.S div = 1mm - 0.9mm = 0.1mm


(d) What is meant by zero error?


Ans: Zero error refers to a mistake in measurement when the instrument does not read zero when the object being measured is absent.


Q10: State least count and Vernier scale reading as shown in the figure and hence, find the length.


Ans: Answer would depend on the provided figure for precise calculation. The least count is typically determined by the difference in values between the Vernier and main scale readings.


Additional Short Questions:


Q1: What is a physical quantity?


Ans: A physical quantity is any property of an object or phenomenon that can be measured such as length, mass, time or temperature.


Q2: What is a non-physical quantity?


Ans:A non-physical quantity is a quantity that cannot be measured using physical instruments.

Examples: Beauty, honesty, love, and happiness.


Q3: What is the Si unit of temperature?


Ans: The SI unit of temperature is Kelvin (K).


Q4: What is a derived quantity?


Ans: A derived quantity is a physical quantity that is derived from base relationships, such as speed (m/s) or force (N). quantities through mathematical


Q5: What is the unit of force in Sl system?


Ans:  The SI unit of force is Newton (N).



Q6: What.is the importance of using standard units in measurements?


Ans: Standard units are important because they ensure consistency and uniformity in measurements across the world. This standardization allows scientists and professionals from different countries to communicate effectively, compare results, and avoid misunderstandings or errors in measurements.


Q7: How does parallax error affect the measurement of length with a metre rule?


Ans: Parallax error occurs when the measurement is taken from an angle instead of directly in front of the scale. This can cause incorrect readings, either longer or shorter than the actual length. To avoid parallax error the scale should be viewed directly from above.


Q8: What is the difference between base and derived quantities?


Ans: Base Quantities: These are physical quantities that are independent and cannot be expressed in terms of other physical quantities.

Examples: Length, mass, time, and temperature.

Derived Quantities: These are physical quantities obtained by combining two or more base quantities.

Examples: Speed, force, area, and volume.

Main Difference: Base quantities are independent, while derived quantities are obtained from base quantities.



29: What is the least count of an instrument?


Ans. The least count of an instrument is the smallest reading that can be accurately measured with that instrument.


Q10: What is the main difference between a microme screw gauge and a Vernier caliper?


Ans: Vernier Calliper:


It is used to measure the length 1/10th of a millimeter. It has L.C 0.1mm.


Screw Gauge:


It is used to measure the lengths 1/100th of a millimeter. It has L.C 0.01mm.


Q12: How can you correct a positive zero error in a Vernier caliper?


Ans: A positive zero error in a Vernier caliper can be corrected by subtracting the zero error from the observed reading.

Formula:

Correct reading = Observed reading − Zero error

Example:
If the zero error is +0.02 cm and the observed reading is 2.50 cm:

Correct reading = 2.50 − 0.02 = 2.48 cm.



013: What is the purpose of the ratchet in a screw gauge?


Ans: The ratchet in a screw gauge is used to apply uniform pressure while measuring, ensuring that the measurement is accurate and consistent, and C preventing over-tightening of the spindle on the object being measured.


Q14: How can we round the number if the last digit is 5?


Ans: If the last digit is 5, we increase the digit before it by 1 and remove 5 and the digits after it.

Example:

  • 2.5 ≈ 3

  • 4.5 ≈ 5

  • 6.75 ≈ 6.8 (to 1 decimal place)

This is called rounding off.


Q15: How is a digit round off? Give an example?


Ans: A number is rounded off to a certain number of significant figures as:



i. If the last digit is more than 5, the retained digit is increased by one.


ii. If it is less than 5, it is retained as such.


For example:


i. Round to 2 significant figures of 2.512x10³m 2.5x103m


ii. Round to 3 significant figures of 3.4567x104kg 3.46x104kg


Q16: Differentiate between precision and accuracy.


Ans: Accuracy: Accuracy is the closeness of a measured value to the true or actual value.

Precision: Precision is the closeness of repeated measurements to each other.

Example:

  • Accuracy means getting the correct measurement.

  • Precision means getting almost the same measurement every time.

Main Difference: Accuracy is about correctness, while precision is about consistency.


Q17: What is meant by uncertainty in a measurement?


Ans: Uncertainty in a measurement refers to the doubt with which the true value of the measured quantity is expected to lie.


Q18: What is the main reason for uncertainty in a measurement?


Ans: The main reason is the type of instrument being used. We know that every measuring instrument is calibrated to a certain small division and this fact puts a limit to the degree of accuracy which can be achieved while measuring with it.


Q19: How can uncertainty in a measurement be reduced? The uncertainty in a measurement can be reduced by taking multiple readings and then finding the average value.


Q20: What is human error in a measurement?



Ans: Human errors occur due to personal performance. The limitation of human perception such as the inability to perfectly estimate the position of the pointer on a scale



Q21: How is human error reduced?


Ans:Human error can be reduced by:

  1. Taking measurements carefully.

  2. Repeating measurements several times.

  3. Using proper measuring instruments.

  4. Reading the scale at eye level.

  5. Taking the average of repeated readings.


Q22: What are systematic errors?


Ans: Systematic errors refer to an effect that influences all measurements of particular measurements equally; it produces a consistent difference in reading. It occurs due to some definite rule. It may occur due to zero errors of instruments, poor calibration of instrument or incorrect marking.


Q23: How systematic error is reduced?


Ans. Systematic error can be reduced by:

  1. Calibrating measuring instruments properly.

  2. Correcting zero error.

  3. Using accurate measuring instruments.

  4. Following proper measurement techniques.

  5. Checking instruments regularly.



Q24: What are Random errors? How is it reduced?


Ans: Random errors occur when repeated measurements of a quantity give different values under the same conditions. It is due to some unknown causes which are unpredictable.


This error can be reduced by using several readings and then taking their average or mean value.



Q25: Does non-physical quantities have dimension?


Ans


Dimension tells us what we are measuring but non-physical quantities cannot be measured so, they have no dimensions.


Constructed Response Questions:



Q2: Why might a standard system of measurement be helpful to a tailor?


Ans: A standard system of measurement allows the tailor to accurately measure fabric and ensure proper fitting for customers, avoiding confusion and inconsistency in clothing sizes.



Q3: The minimum main scale reading of a micrometer screw gauge is 1mm and there are 100 divisions on the circular scale. When the thimble is rotated once, 1 mm is its measurement on the main scale. What is the least count of the instrument? The reading for thickness of a steel rod as shown in the figure. What is the thickness of the rod?


Ans: Least count of screw gauge


= 0.01 mm


Main scale reading


= 9mm


Considering point


= 70


Multiplying by L.C.


= 0.01 x 70 = 0.7mm


Exact reading


= 9+ 9 +0.7


=9.7mm


Q4: You are provided a metre scale and a bundle of pencil; how can the diameter of a pencil be measured using the metre scale with the same precision as that of Vernier Callipers? Describe briefly.


Ans: To measure the diameter of a pencil using the meter scale with the same precision, you can place the pen on the scale to measure the distance between the edges using the scale's smallest divisions. By taking multiple readings and averaging them, precision can be improved.


Q5: The end of a metre scale is worn out. Where would you place a pencil to find the length?


Ans: To measure accurately, place the pencil near the undamaged end of the scale and ensure t measurement starts from zero point of the scale.


Q6: Why is it better to place the object close to the metre scale?


Ans: Placing the object close to the metre scale reduces the chances of parallax error and ensures more accurate reading.


Q7: Why is a standard unit needed to measure a quantity correctly?


Ans: A standard unit ensures consistency and universal understanding; allowing measurements to be universally accepted and compared accurately.


Q8: Suggest some natural phenomena that could serve as a reasonably accurate time standard.


Ans: Some natural phenomena that could serve as time standards include the rotation of the Earth (a day) the Earth's orbit around the Sun (a year). Radioactive decay and solar cycle.


Q9: It is difficult to locate the meniscus in a wider vessel. Why?


Ans: In a wider castle, the curve of the meniscus becomes less pronounced and harder to observe clearly, making it difficult to determine the exact point of measurement.


Q10: Which instrument can be used to measure?


Ans:


(i) Internal diameter of a test tube:


Vernier calipers can be used to measure the internal diameter.


(ii) Depth of a beaker:


Depth gauge can be used to measure the depth of beaker.


Exercise (MCQ'S)


Answers:


(i) (d), 

(ii) (b), 

(iii) (c), 

(iv) (c), 

(v) (d) 

(vi) (b) 

(vii) (d) 

(viii) (b) 

(ix)(c) 

(x) (b)

(xi) (c)




https://www.physicsnotes.online/















Post a Comment

0 Comments